View FAN7930_5771419.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

april 2010 ? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 FAN7930 ? critical conducti on mode pfc controller FAN7930 critical conduction mode pfc controller features ? pfc ready signal ? input voltage absent detection circuit ? maximum switching frequency limitation ? internal soft-start and startup without overshoot ? internal total harmonic distortion (thd) optimizer ? precise adjustable output over-voltage protection ? open-feedback protection and disable function ? zero current detector ? 150 s internal startup timer ? mosfet over-current protection ? under-voltage lockout with 3.5v hysteresis ? low startup and operating current ? totem-pole output with high state clamp ? + 500/-800ma peak gate drive current ? 8-pin sop applications ? adapter ? ballast ? lcd tv, crt tv ? smps description the FAN7930 is an active power factor correction (pfc) controller for boost pfc applications that operate in critical conduction mode (crm). it uses a voltage-mode pwm that compares an internal ramp signal with the error amplifier output to generate a mosfet turn-off signal. because the voltage-mode crm pfc controller does not need rectified ac line voltage information, it saves the power loss of an input voltage sensing network necessary for a current-mode crm pfc controller. FAN7930 provides over-voltage protection, open- feedback protection, over-current protection, input- voltage-absent detection, and under-voltage lockout protection. the pfc-ready pin can be used to trigger other power stages when pfc output voltage reaches the proper level with hysteresis. the FAN7930 can be disabled if the inv pin voltage is lower than 0.45v and the operating current decreases to a very low level. using a new variable on-time control method, thd is lower than the conventional crm boost pfc ics. related resources an-8035 ? design consideration for boundary conduction mode pfc using FAN7930 ordering information part number operating temperature range top mark package packing method FAN7930m -40 to +125c FAN7930 8-lead small outline package (sop) rail FAN7930mx tape & reel
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 2 FAN7930 ? critical conducti on mode pfc controller application diagram figure 1. typical boost pfc application internal block diagram figure 2. functional block diagram
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 3 FAN7930 ? critical conducti on mode pfc controller pin configuration figure 3. pin configuration (top view) pin definitions pin # name description 1 inv this pin is the inverting input of the error amplifier. the output voltage of the boost pfc converter should be resistively divided to 2.5v. 2 rdy this pin is used to detect pfc output voltage reaching a pre-determined value. when output voltage reaches 89% of rated output voltage, this pin is pulled high, which is an (open drain) output type. 3 comp this pin is the output of the transconductance error amplifier. components for the output voltage compensation should be connected between this pin and gnd. 4 cs this pin is the input of the over-current protection comparator. the mosfet current is sensed using a sensing resistor and the resulting voltage is applied to this pin. an internal rc filter is included to filter switching noise. 5 zcd this pin is the input of the zero-current detection block. if the voltage of this pin goes higher than 1.5v, then goes lower than 1.4v, the mosfet is turned on. 6 gnd this pin is used for the ground potential of all the pins. for proper operation, the signal ground and the power ground should be separated. 7 out this pin is the gate drive output. the peak sourci ng and sinking current levels are +500ma and - 800ma, respectively. for proper operation, the stray inductance in the gate driving path must be minimized. 8 v cc this is the ic supply pin. ic current and mosfet drive current are supplied using this pin.
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 4 FAN7930 ? critical conducti on mode pfc controller absolute maximum ratings stresses exceeding the absolute maximum ratings may damage the device. the device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. in addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. the absolute maximum ratings are stress ratings only. symbol parameter min. max. unit v cc supply voltage v z v i oh , i ol peak drive output current -800 +500 ma i clamp driver output clamping diodes v o >v cc or v o <-0.3v -10 +10 ma i det detector clamping diodes -10 +10 ma v in error amplifier input, output, zcd and rdy pin (1) -0.3 8.0 v cs input voltage (2) -10.0 6.0 t j operating junction temperature +150 c t a operating temperature range -40 +125 c t stg storage temperature range -65 +150 c esd electrostatic discharge capability human body model, jesd22-a114 2.5 kv charged device model, jesd22-c101 2.0 notes: 1. when this pin is supplied by external power sources by accident, its maximum allowable current is 50ma. 2. in case of dc input, acceptable input range is -0.3v~6v: within 100ns -10v~6v is acceptable, but electrical specifications are not guaranteed during such a short time. thermal impedance symbol parameter min. max. unit ja thermal resistance, junction-to-ambient ( 3 ) 150 c/w note: 3. regarding the test environment and pcb type, please refer to jesd51-2 and jesd51-10.
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 5 FAN7930 ? critical conducti on mode pfc controller electrical characteristics v cc = 14v, t a = -40c~+125c, unless otherwise specified. symbol parameter conditions min. typ. max. units v cc section v start start threshold voltage v cc increasing 11 12 13 v v stop stop threshold voltage v cc decreasing 7.5 8.5 9.5 v hy uvlo uvlo hysteresis 3.0 3.5 4.0 v v z zener voltage i cc =20ma 20 22 24 v v op recommended operating range 13 20 v supply current section i start startup supply current v cc =v start -0.2v 120 190 a i op operating supply current output not switching 1.5 3.0 ma i dop dynamic operating supply current 50khz, c i =1nf 2.5 4.0 ma i opdis operating current at disable v inv =0v 90 160 230 a error amplifier section v ref1 voltage feedback input threshold1 t a =25c 2.465 2.500 2.535 v v ref1 line regulation v cc =14v~20v 0.1 10.0 mv v ref2 temperature stability of v ref1 (4) 20 mv i ea,bs input bias current v inv =1v~4v -0.5 0.5 a i eas,sr output source current v inv =v ref -0.1v -12 a i eas,sk output sink current v inv =v ref +0.1v 12 a v eah output upper clamp voltage v inv =1v, v cs =0v 6.0 6.5 7.0 v v eaz zero duty cycle output voltage 0.9 1.0 1.1 v g m transconductance (4) 90 115 140 mho maximum on-time section t on,max1 maximum on-time programming 1 t a =25c, v zcd =1v 35.5 41.5 47.5 s t on,max2 maximum on-time programming 2 t a =25c, i zcd =0.469ma 11.2 13.0 14.8 s current-sense section v cs current sense input threshold voltage limit 0.7 0.8 0.9 v i cs,bs input bias current v cs =0v~1v -1.0 -0.1 1.0 a t cs,d current sense delay to output (4) dv/dt=1v/100ns, from 0v to 5v 350 500 ns continued on the following page?
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 6 FAN7930 ? critical conducti on mode pfc controller electrical characteristics v cc = 14v, t a = -40c~+125c, unless otherwise specified. symbol parameter conditions min. typ. max. units zero-current detect section v zcd input voltage threshold (4) 1.35 1.50 1.65 v hy zcd detect hysteresis (4) 0.05 0.10 0.15 v v clamph input high clamp voltage i det =3ma 5.5 6.2 7.5 v v clampl input low clamp voltage i det = -3ma 0 0.65 1.00 v i zcd,bs input bias current v zcd =1v~5v -1.0 -0.1 1.0 a i zcd,sr source current capability (4) t a =25c -4 ma i zcd,sk sink current capability (4) t a =25c 10 ma t zcd,d maximum delay from zcd to output turn-on (4) dv/dt=-1v/100ns, from 5v to 0v 100 200 ns output section v oh output voltage high i o =-100ma, t a =25c 9.2 11.0 12.8 v v ol output voltage low i o =200ma, t a =25c 1.0 2.5 v t rise rising time (4) c in =1nf 50 100 ns t fall falling time (4) c in =1nf 50 100 ns v o,max maximum output voltage v cc =20v, i o =100a 11.5 13.0 14.5 v v o,uvlo output voltage with uvlo activated v cc =5v, i o =100a 1 v restart / maximum switching frequency limit section t rst restart timer delay 50 150 300 s f max maximum switching frequency (4) 250 300 350 khz rdy pin i rdy,sk output sink current 1 2 4 ma v rdy,sat output saturation voltage i rdy,sk =2ma 320 500 mv i rdy,lk output leakage current output high impedance 1 a soft-start timer section t ss internal soft-soft (4) 3 5 7 ms uvlo section v rdy output ready voltage 2.185 2.240 2.295 v hy rdy output ready hysteresis 0.600 v protections v ovp ovp threshold voltage t a =25c 2.620 2.675 2.730 v hy ovp ovp hysteresis t a =25c 0.120 0.175 0.230 v v en enable threshold voltage 0.40 0.45 0.50 v hy en enable hysteresis 0.050 0.10 0.15 v t sd thermal shutdown temperature (4) 125 140 155 c t hys hysteresis temperature of tsd (4) 60 c note: 4. these parameters, although guaranteed by design, are not production tested.
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 7 FAN7930 ? critical conducti on mode pfc controller comparison of fan7530 and FAN7930 function fan7530 FAN7930 FAN7930 advantages pfc ready pin none integrated ? no external circuit for pfc output uvlo ? reduction of power loss and bom cost caused by pfc out uvlo circuit ? open-drain pin has versatile uses frequency limit none integrated ? abnormal ccm operation prohibited ? abnormal inductor current accumulation can be prohibited ac absent detection none integrated ? increase system reliability with ac on-off test ? guarantee stable operation at short electric power failure soft-start and overshoot-less none integrated ? reduce voltage and current stress at startup ? eliminate audible noise due to unwanted ovp triggering thd optimizer external internal ? no external resistor is needed tsd none 140c with 60c hysteresis ? stable and reliable tsd operation ? converter temperature range limited range
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 8 FAN7930 ? critical conducti on mode pfc controller typical performance characteristics figure 4. v oltage feedback input threshold 1 (v ref1 ) vs. t a figure 5. start threshold voltage (v start ) vs. t a figure 6. stop threshold voltage (v stop ) vs. t a figure 7. startup supply current (i start ) vs. t a figure 8. operating supply current (i op ) vs. t a figure 9. output upper clamp voltage (v eah ) vs. t a
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 9 FAN7930 ? critical conducti on mode pfc controller typical performance characteristics figure 10. zero duty cycle output voltage (v eaz ) vs. t a figure 11. maximum on-time program 1 (t on,max1 ) vs. t a figure 12. maximum on-time program 2 (t on,max2 ) vs. t a figure 13. current sense input threshold voltage limit (v cs ) vs. t a figure 14. input high clamp voltage (v clamph ) vs. t a figure 15. input low clamp voltage (v clampl ) vs. t a
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 10 FAN7930 ? critical conducti on mode pfc controller typical performance characteristics figure 16. output voltage high (v oh ) vs. t a figure 17. output v oltage low (v ol ) vs. t a figure 18. restart timer delay (t rst ) vs. t a figure 19. output ready voltage (v rdy ) vs. t a figure 20. output saturation voltage (v rdy,sat ) vs. t a figure 21. ovp threshold voltage (v ovp ) vs. t a
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 11 FAN7930 ? critical conducti on mode pfc controller applications information 1. startup : normally, supply voltage (v cc ) of a pfc block is fed from the additional power supply, which can be called standby power. without this standby power, auxiliary winding to detect zero current detection can be used as a supply source. once the supply voltage of the pfc block exceeds 12v, internal operation is enabled until the voltage drops to 8.5v. if v cc exceeds v z , 20ma current is sinking from v cc . figure 22. startup circuit 2. inv block : scaled-down voltage from the output is the input for the inv pin. many functions are embedded based on the inv pin: transconductance amplifier, output ovp comparator, disable comparator, and output uvlo comparator. for the output voltage control, a transconductance amplifier is used instead of the conventional voltage amplifier. the transconductance amplifier (voltage- controlled current source) aids the implementation of ovp and disable function. the output current of the amplifier changes according to the voltage difference of the inverting and non-inverting input of the amplifier. to cancel down the line input voltage effect on power factor correction, effective control response of pfc block should be slower than the line frequency and this conflicts with the transient response of controller. two- pole one-zero type compensation may be used to meet both requirements. the ovp comparator shuts down the output drive block when the voltage of the inv pin is higher than 2.675v and there is 0.175v hysteresis. the disable comparator disables the operation when the voltage of the inverting input is lower than 0.35v and there is 100mv hysteresis. an external small-signal mosfet can be used to disable the ic, as shown in figure 23. the ic operating current decreases to reduce power consumption if the ic is disabled. figure 24 is the timing chart of the internal circuit near the inv pin when rated pfc output voltage is assumed at 390v dc and v cc supply voltage is 15v. figure 23. circuit around inv pin 390vdc 2.50v 2.65v 0.45v current sourcing current sourcing i sinking 0.35v 1.64v 2.24v 2.50v 2.0v 349v 413v 390v 256v 70v 55v v out pfc v inv v cc i out comp disable v rdy ovp t voltage is decided by pull-up voltage. vcc<2v, internal logic is not alive. - rdy pin is floating, so pull up voltage is shown. - internal signals are unknown. 15v figure 24. timing chart for inv block 3. rdy output : when the inv voltage is higher than 2.24v, output uvlo voltage is triggered to high and lasts until the inv voltage is lower than 1.64v. this signal outputs through the rdy pin. rdy pin output is open-drain type, so needs an external pull-up resistor to supply the proper power source. the rdy pin output remains floating until v cc is higher than 2v.
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 12 FAN7930 ? critical conducti on mode pfc controller 4. zero-current detection : zero-current detection (zcd) generates the turn-on signal of the mosfet when the boost inductor current reaches zero using an auxiliary winding coupled with the inductor. when the power switch turns on, negative voltage is induced at the auxiliary winding due to the opposite winding direction (see equation 1) and positive voltage is induced (see equation 2) when the power switch turns off. ac ind aux aux v t t v ? ? = (1) () ac pfcout ind aux aux v v t t v ? ? = (2) where, v aux is the auxiliary winding voltage, t ind and t aux are boost inductor turns and auxiliary winding turns respectively, v ac is input voltage for pfc converter and v out_pfc is output voltage from the pfc converter. figure 25. circuit near zcd because auxiliary winding voltage can swing from negative voltage to positive voltage, the internal block in zcd pin has both positive and negative voltage clamping circuits. when the auxiliary voltage is negative, internal circuit clamps the negative voltage at the zcd pin around 0.65v by sourcing current to the serial resistor between the zcd pin and the auxiliary winding. when the auxiliary voltage is higher than 6.5v, current is sinked through a resistor from the auxiliary winding to the zcd pin. figure 26. auxiliary voltage depends on mosfet switching to check the boost inductor current zero instance, auxiliary winding voltage is used. when boost inductor current becomes zero, there is a resonance between boost inductor and all capacitors at mosfet drain pin, including c oss of the mosfet; an external capacitor at the d-s pin to reduce the voltage rising and falling slope of the mosfet; a parasitic capacitor at inductor; and so on to improve performance. resonated voltage is reflected to the auxiliary winding and can be used as detecting zero current of boost inductor and valley position of mosfet voltage stress. for valley detection, a minor delay by the resistor and capacitor is needed. a capacitor increases the noise immunity at the zcd pin. if zcd voltage is higher than 1.5v, an internal zcd comparator output becomes high and low when the zcd goes below 1.4v. at the falling edge of comparator output, internal logic turns on the mosfet. figure 27. auxiliary voltage threshold when no zcd signal is available, the pfc controller cannot turn on mosfet, so the controller checks every switching off time and forces mosfet turn on when the off time is longer than 150 s. it is called restart timer. restart timer triggers mosfet turn on at startup and may be used at the input voltage zero cross period. s 150 figure 28. restart timer at startup
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 13 FAN7930 ? critical conducti on mode pfc controller because the mosfet turn on depends on the zcd input, switching frequency may increase to higher than several megahertz due to the miss-triggering or noise on the nearby zcd pin. if the switching frequency is higher than needed for critical conduction mode (crm), operation mode shifts to continuous conduction mode (ccm). in ccm, unlike crm where the boost inductor current is reset to zero at the next switch on; inductor current builds up at every switching cycle and can be raised to very high current, that exceeds the current rating of the power switch or diode. this can seriously damage the power switch and result in burn down. to avoid this, maximum switching frequency limitation is embedded. if zcd signal is applied again within 3.3 s after the previous rising edge of gate signal, this signal is ignored internally and FAN7930 waits for another zcd signal. this slightly degrades the power factor performance at light load and high input voltage. figure 29. maximum switching frequenc y limit operation 5. control : the scaled output is compared with the internal reference voltage and sinking or sourcing current is generated from the comp pin by the transconductance amplifier. the error amplifier output is compared with the internal sawtooth waveform to give proper turn-on time based on the controller. figure 30. control circuit unlike a conventional voltage-mode pwm controller, FAN7930 turns on the mosfet at the falling edge of zcd signal. on instance is decided by the external signal and the turn-on time lasts until the error amplifier output (v comp ) and sawtooth waveform meet. when load is heavy, output voltage decreases, scaled output decreases, comp voltage increases to compensate low output, turn-on time lengthens to give more inductor turn-on time, and increased inductor current raises the output voltage. this is how pfc negative feedback controller regulates output. the maximum of v comp is limited to 6.5v, which dictates the maximum turn-on time, and switching stops when v comp is lower than 1.0v. s / v 155 . 0 figure 31. turn-on time determination the roles of pfc controller are regulating output voltage and input current shaping to increase power factor. duty control based on the output voltage should be fast enough to compensate output voltage dip or overshoot. for the power factor, however, the control loop must not react to the fluctuating ac input voltage. these two requirements conflict; therefore, when designing a feedback loop, the feedback loop should be least 10 times slower than ac line frequency. that slow response is made by c1 at compensator. r1 makes gain boost around operation region and c2 attenuates gain at higher frequency. boost gain by r1 helps raise the response time and improves phase margin. figure 32. compensators gain curve for the transconductance error amplifier side, gain changes based on differential input. when the error is large, gain is large to make the output dip or peak to suppress quickly. when the error is small, low gain is used to improve power factor performance.
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 14 FAN7930 ? critical conducti on mode pfc controller mho 250 mho 115 figure 33. gain characteristic 6. soft-start : when v cc touches v start , internal reference voltage is increased like a stair step for 5ms. as a result, v comp is also raised gradually and mosfet turn-on time increases smoothly. this reduces voltage and current stress on the power switch during startup. figure 34. soft-start sequence 7. ?overshoot-less? startup : feedback control speed of pfc is quite slow. due to the slow response, there is a gap between output voltage and feedback control. that is why over-voltage protection (ovp) is critical at the pfc controller and voltage dip caused by fast load changes from light to heavy is diminished by a bulk capacitor. ovp is easily triggered at startup phase. operation on and off by ovp at startup may cause audible noise and can increase voltage stress at startup, which is normally higher than in normal operation. this operation is better when soft-start time is very long. however, too long startup time enlarges the output voltage building time at light load. FAN7930 has ?overshoot-less? control at startup. during startup, the feedback loop is controlled by an internal proportional gain controller and when the output voltage reaches the rated value, it switches to an external compensator after a transition time of 30ms. in short, an internal proportional gain controller eliminates overshoot at startup and an external conventional compensator takes over successfully afterward. figure 35. overshoot-less startup control 8. thd optimization : total harmonic distortion (thd) is the factor that dictates how closely input current shape matches sinusoidal form. the turn-on time of the pfc controller is almost constant over one ac line period due to the extremely low feedback control response. the turn-off time is decided by the current decrease slope of the boost inductor made by the input voltage and output voltage. once inductor current becomes zero, resonance between c oss and the boost inductor makes oscillating waveforms at the drain pin and auxiliary winding. by checking the auxiliary winding voltage through the zcd pin, the controller can check the zero current of boost inductor. at the same time, a minor delay time is inserted to determine the valley position of drain voltage. the input and output voltage difference is at its maximum at the zero cross point of ac input voltage. the current decrease slope is steep near the zero cross region and more negative inductor current flows during a drain voltage valley detection time. such a negative inductor current cancels down the positive current flows and input current becomes zero, called ?zero-cross distortion? in pfc.
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 15 FAN7930 ? critical conducti on mode pfc controller 1.5v 150ns 1.4v on FAN7930 rev.00 v zcd t i inductor mosfet gate i negative on i in i mosfet i diode figure 36. input and output current near input voltage peak figure 37. input and output current near input voltage peak zero cross to improve this, lengthened turn-on time near the zero cross region is a well-known technique, though the method may be different from company to company and may be proprietary. FAN7930 emdodies this by sourcing current through the zcd pin. auxiliary winding voltage becomes negative when the mosfet turns on and is proportional to input voltage. the negative clamping circuit of zcd outputs the current to maintain the zcd voltage at a fixed value. the sourcing current from the zcd is directly proportional to the input voltage. some portion of this current is applied to the internal sawtooth generator together with a fixed-current source. theoretically, the fixed-current source and the capacitor at sawtooth generator decide the maximum turn-on time when no current is sourcing at zcd clamp circuit and available turn-on time gets shorter proportional to the zcd sourcing current. figure 38. circuit of thd optimizer figure 39. effect of thd optimizer by thd optimizer, turn-on time over one ac line period is proportionally changed, depending on input voltage. near zero cross, lengthened turn-on time improves thd performance. 9. input voltage absent detection : to save power loss caused by input voltage sensing resistors and to optimize thd easily, the FAN7930 omits ac input voltage detection. therefore, no information about ac input is available from the internal controller. in many cases, the v cc of pfc controller is supplied by a independent power source like standby power. in this scheme, some mismatch may exist. for example, when the electric power is suddenly interrupted during two or three ac line periods; v cc is still alive during that time, but output voltage drops because there is no input power source. consequently, the control loop tries to compensate for the output voltage drop and v comp reaches its maximum. this lasts until ac input voltage is
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 16 FAN7930 ? critical conducti on mode pfc controller live again. when ac input voltage is live again, high v comp allows high switching current and more stress is put on the mosfet and diode. to protect against this, FAN7930 internally checks if the input ac voltage exists. if input does not exist, soft-start is reset and waits until ac input is live again. soft-start manages the turn-on time for smooth operation when it detects ac input is applied again and applies less voltage and current stress on startup. figure 40. operation without input voltage absent circuit figure 41. operation with input voltage absent circuit 10. current sense : the mosfet current is sensed using an external sensing resistor for the over-current protection. if the cs pin voltage is higher than 0.8v, the over-current protection comparator generates a protection signal. an internal rc filter of 40k ? and 8pf is included to filter switching noise. 11. gate driver output : FAN7930 contains a single totem-pole output stage designed for a direct drive of the power mosfet. the drive output is capable of up to +500/-800ma peak current with a typical rise and fall time of 50ns with 1nf load. the output voltage is clamped to 13v to protect the mosfet gate even if the v cc voltage is higher than 13v.
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 17 FAN7930 ? critical conducti on mode pfc controller pcb layout guide pfc block normally handles high switching current and the voltage low energy signal path can be affected by the high energy path. cautious pcb layout is mandatory for stable operation. 1. the gate drive path should be as short as possible. the closed-loop that starts from the gate driver, mosfet gate, and mosfet source to ground of pfc controller is recommended as close as possible. this is also crossing point between power ground and signal ground. power ground path from the bridge diode to the output bulk capacitor should be short and wide. the sharing position between power ground and signal ground should be only at one position to avoid ground loop noise. signal path of pfc controller should be short and wide for external components to contact. 2. pfc output voltage sensing resistor is normally high to reduce current consumption. this path can be affected by external noise. to reduce noise possibility at the inv pin, a shorter path for output sensing is recommended. if a shorter path is not possible, place some dividing resistors between pfc output and the inv pin ? closer to the inv pin is better. relative high voltage close to the inv pin can be helpful. 3. zcd path is recommended close to auxiliary winding from boost inductor and to the zcd pin. if that is difficult, place a small capacitor (below 50pf) to reduce noise. 4. switching current sense path should not share with another path to avoid interference. some additional components may be needed to reduce the noise level applied to the cs pin. 5. a stabilizing capacitor for v cc is recommended as close as possible to the v cc and ground pins. if it is difficult, place the smd capacitor as close to the corresponding pins as possible. figure 42. recommended pcb layout
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 18 FAN7930 ? critical conducti on mode pfc controller typical application circuit application device input voltage range rated output power output voltage (maximum current) lcd tv power supply FAN7930 90-265v ac 195w 390v (0.5a) features ? average efficiency of 25%, 50%, 75%, and 100% load conditions is higher than 95% at universal input. ? power factor at rated load is higher than 0.98 at universal input. ? total harmonic distortion (thd) at rated load is lower than 15% at universal input. key design notes ? when auxiliary v cc supply is not available, v cc power can be supplied through zero current detect (zcd) winding. the power consumption of r103 is quite high, so its power rating needs checking. ? because the input bias current of inv pin is almost zero, output voltage sensing resistors (r112~r115) as high as possible. however, too-high resistance makes the node easily affected by noise. thus values need to strike a balance between power consumption and noise immunity. ? quick charge diode (d106) can be eliminated. without d106 , system operation is normal due to the controller?s highly reliable protection features. 1. schematic figure 43. demonstration circuit
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 19 FAN7930 ? critical conducti on mode pfc controller 2. transformer figure 44. transformer schematic diagram of FAN7930 3. winding specification position no pin (s f) wire turns winding method barrier tape top bot ts bottom n p 9, 10 7, 8 0.1 50 49 solenoid winding 1 insulation: polyester tape t = 0.025mm, 3 layers top n aux 2 4 0.3 6 solenoid winding insulation: polyester tape t = 0.025mm, 4 layers 4. electrical characteristics pin specification remark inductance 9, 10 7, 8 230 h 7% 100khz, 1v 5. core & bobbin core: eer3124, samhwa (pl-7) (ae=97.9mm 2 ) bobbin: eer3124
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 20 FAN7930 ? critical conducti on mode pfc controller 6. bill of materials part # value note part # value note resister switch r101 1m 1w q101 fcpf20n60 20a, 600v, superfet r102 330k 1/2w diode r103 10k 1w d101 1n4746 1w, 18v, zener diode r104 30k 1/4w d102 uf4004 1a, 400v glass passivated high-efficiency rectifier r107 10k 1/4w d103 1n4148 1a, 100v small-signal diode r108 4.7k 1/4w d104 1n4148 1a, 100v small-signal diode r109 47k 1/4w d105 8a, 600v, general-purpose rectifier r110 10k 1/4w d106 3a, 600v, general-purpose rectifier r111 0.80k 5w r112, 113, 114 3.9k 1/4w ic101 FAN7930 crm pfc controller r115 75k 1/4w capacitor fuse c101 220nf/275v ac box capacitor fs101 5a/250v c102 680nf/275v ac box capacitor ntc c103 0.68f/630v box capacitor th101 5d-15 c104 12nf/50v ceramic capacitor bridge diode c105 100nf/50v smd (1206) bd101 15a, 600v c107 33f/50v electrolytic capacitor line filter c108 220nf/50v ceramic capacitor lf101 23mh c109 47nf/50v ceramic capacitor transformer c110 1nf/50v ceramic capacitor t1 eer3124 ae=97.9mm 2 c112 47nf/50v ceramic capacitor znr c111 220f/450v electrolytic capacitor znr101 10d471 c114 2.2nf/450v box capacitor c115 2.2nf/450v box capacitor
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 21 FAN7930 ? critical conducti on mode pfc controller physical dimensions figure 45. 8-lead small outline package (sop) package drawings are provided as a service to customers considering fairchild components. drawings may change in any manner without notice. please note the revision and/or date on the drawing and contact a fairchild semiconductor representative to ver ify or obtain the most recent revision. package specifications do not expand the terms of fairchild?s worldwide terms and conditions, specifically the warranty therein, which covers fairchild products. always visit fairchild semiconductor?s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/ . 8 0 see detail a notes: unless otherwise specified a) this package conforms to jedec ms-012, variation aa, issue c, b) all dimensions are in millimeters. c) dimensions do not include mold flash or burrs. d) landpattern standard: soic127p600x175-8m. e) drawing filename: m08arev13 land pattern recommendation seating plane c gage plane x 45 detail a scale: 2:1 pin one indicator 4 8 1 b 5 a 5.60 0.65 1.75 1.27 6.20 5.80 3.81 4.00 3.80 5.00 4.80 (0.33) 1.27 0.51 0.33 0.25 0.10 1.75 max 0.25 0.19 0.36 0.50 0.25 r0.10 r0.10 0.90 0.40 (1.04) option a - bevel edge option b - no bevel edge 0.25 cba 0.10 c
? 2010 fairchild semiconductor corporation www.fairchildsemi.com FAN7930 ? rev. 1.0.1 22 FAN7930 ? critical conducti on mode pfc controller

▲Up To Search▲

Price & Availability of FAN7930

	To Download FAN7930 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .